Context 142 - November 2015

30 C O N T E X T 1 4 2 : N O V E M B E R 2 0 1 5 For EFFESUS, a new insulating lime mortar was developed by the Dutch partner Bofimex. Various insulating mortars were considered at the start of the EFFESUS project, of which none was based on a lime binder.Whereas the inherent material properties of lime mortars, especially their lower strength development and higher vapour permeability and moisture absorption compared to cement-based mortars, make them particularly suitable for use with historical masonry, their thermal insulating properties are deficient. The Bofimex mortar, ISOCAL, is based on natural hydraulic lime (NHL), combined with extruded polystyrene beads as insulant and other additives.As mortar, an NHL 5 is used, which is a higher-strength mortar in the NHL range. However, because the polystyrene filler content is up to 80 per cent, the resulting mortar is substantially weaker and more permeable than ordinary NHL 5 mortars, making the new product better suited for use as render and plaster for historical masonry. The new mortar was trialled first in the laboratories of the German consortium partner MPA Stuttgart, the material testing institute of the University of Stuttgart. A field trial was then conducted by another German partner, Fraunhofer-Gesellschaft, at the outdoor test site in Holzkirchen of their Institute for Building Physics, where a timber-framed test house already exists. The insulating render was applied to the west-facing wall, to a brick infill panel set into the timber frame. The performance measurements are continuing. The location in Bavaria’s Alpine foothills has, for Germany, harsh climatic conditions, with severe wind-driven rain exposure, high radiation heat losses during nights and frequent freeze-thaw cycles.The west-facing wall receives the extremes of weathering loads – the harshest test conditions for the applied mortar. In parallel, the mortar has been applied as a plaster in the nearby case study in Benediktbeuern, at the Fraunhofer Centre for Conservation and Energy Performance of Historic Buildings, located in the historic cooperage of the town’s Baroque monastery. Here the plaster’s hygrothermal performance is being closely monitored under controlled climatic indoor conditions. The Scottish product development is aerogel fibre insulation, formulated initially to meet the extreme conditions of outer space exploration.The new product, SpaceLoft, is produced by the consortium partner A Proctor Group (APG), using aerogel supplied by the American company Aspen Aerogel. For EFFESUS, the prompt for developing this product related to the traditional use of plaster on laths as an internal wall finish, often to be found in Britain. This historical construction includes air cavities between the battens supporting the laths.Where these cavities are not required for moisture evaporation from the masonry, they can be filled by blowing in cavity-fill insulation. This installation process minimises time and costs as well as damage to existing fabric and disruption to building occupants. The retrofitting technique can also be used for cavities behind plasterboard drylining. Existing cavity-fill products have limitations for use with older construction types, such as historical masonry, being vapour-impermeable or water-absorbent, having lower thermal performance or introducing the risk of plasticiser migration. The newly developed product is manufactured from non-woven blankets of polyester fibres impregnated with silica aerogel. Aerogel is a lightweight solid derived from a gel whose liquid component has been replaced with gas.When the liquid is removed, what remains is akin to puffed-up sand, with up to 99 per cent porosity.The result is an extremely low-density material with several remarkable properties,most notably its effectiveness as a thermal insulator that is ultra-light, extremely water repellent and vapour permeable. As with the insulating lime mortar, the aerogel fibre insulation was tested first by MPA Stuttgart before, in early 2015, a real-world case study was set up in Glasgow, Spray application of insulating lime render on a wall forming the enclosure of a climate chamber (Photo: MPA Stuttgart) The Italian partner RED installing equipment for heat-flow measurements of the aerogel retro-fitted wall in the Glasgow tenement case study (Photo: Historic Environment Scotland)

RkJQdWJsaXNoZXIy MjgyMjA=